In this guide
  1. How do you ask about an unclear “mouth diameter”?
  2. What does 24-410 mean?
  3. Where are T, E and I measured?
  4. Which measurements does each part need?
  5. What should you send to the supplier?
  6. Continue your buying brief

Use the full neck finish code to match a screw cap. Check the inside diameter separately if the design uses a stopper or insert. For an open decorative collar, ask which part of the neck holds it in place and how much room the reeds need.

In this guide
Threaded bottle neck showing the outside thread diameter T, the neck diameter E and the inside opening diameter I, with a 24-410 code example
The arrows show where the three diameters are measured. The drawing is schematic and has no scale.

How do you ask about an unclear “mouth diameter”?

Ask which feature and measurement plane the number describes. A nominal thread diameter, the smooth outer neck and an inside bore at the plug engagement depth are different references.

Example enquiry wording

“Please identify the neck drawing and revision for the selected bottle. Mark the external finish and the bore where the proposed insert engages. We will review the named bottle, closure and insert as one assembly; please list any fit or seal checks still open.”

Example wording only. It does not specify a JUNOVA neck size or approve any closure.

Use the product reference to request the drawing, not as a substitute for it. Record the actual component revisions through the sample approval checklist.

What does 24-410 mean?

A neck finish is the part of the bottle that mates with the closure. In the continuous-thread code 24-410, 24 is the nominal outside thread diameter in millimeters. 410 identifies the thread finish style, which describes the thread configuration and finish height. The code leaves the inside opening unspecified. Pretium Packaging explains the two parts of the code and the drawing labels.

Use 24-410 here as an example of how to read a code. For an actual order, confirm the specified finish, tolerances and compatible closure on the relevant drawings. A smooth or proprietary neck needs a drawing of its own profile and mating parts.

Where are T, E and I measured?

Diameter labels on a threaded bottle drawing
LabelMeasurementWhere to check
TOutside diameter across the threadsAcross the outermost edges of the threads.
EOutside neck diameter excluding the threadsAcross the neck itself, at the position marked on the drawing.
IInside diameter of the neck openingAcross the bore where the insert or filling equipment needs clearance.

Ask the supplier to mark the location and tolerance for each relevant measurement. A plug may engage below the rim, so a reading taken only at the top can miss the part of the opening that controls fit. Berlin Packaging shows T, E and I on a finish drawing.

Which measurements does each part need?

Start with the part you are matching
PartWhat to requestWhat to check on the sample
Screw capThe full finish code, T, the finish height and the cap drawing.The cap engages and seats as intended. Check the seal separately for the proposed pack.
Internal stopper or insertThe bore at the engagement depth, its tolerances and the insert drawing.The stopper reaches the intended depth and can be inserted and removed as specified.
Decorative collarThe attachment detail and the clear opening for the reeds. Request the full finish code if the collar screws on.The collar sits in the intended position and the proposed reed bundle passes through its opening.

If a reply says only “28 mm neck,” ask which dimension it describes and request the drawing revision. For the difference between a transport seal and the collar used on display, see the diffuser closure guide.

What should you send to the supplier?

  1. The bottle model and drawing revision, with the required measurement points marked.
  2. The cap or collar reference and its attachment drawing.
  3. The insert reference, engagement depth and required bore dimensions, if an insert is used.
  4. The assembly sample and the checks it needs, such as fit, clearance or transport sealing.

The JN-DB001 triangular diffuser bottle illustrates why the distinction matters. Its catalogue lists an approximate 18 mm mouth diameter. Ask for the dimensioned neck drawing to establish where that diameter is measured and which closure matches the selected sample.

Record the reviewed drawing and sample versions in the sample approval checklist. The custom diffuser bottle guide covers the wider bottle and pack specification.

Browse the glass reed diffuser bottles and share the bottle model and proposed closure through custom glass development.

Continue your diffuser packaging brief

For a project enquiry, send the bottle reference, neck drawing, proposed parts, finish, quantity and destination.

Compare glass diffuser bottles